How To Install A Mailbox In Winter

Home - Diy

How to Replace a Mailbox in the Winter

The wintertime months tin can wreak havoc on your mailbox. Vehicles sliding on the ice, snowplows trying to clear the roads and the extra weight of snowfall and ice can snap and cleft your mailbox and post, damaging them beyond repair. Earlier you tin can install a new mailbox, you lot must remove the sometime mail service and box.

Replacing a mailbox in winter can be challenging.

This can be a difficult task during the wintertime season. The dropping temperatures typically freeze the ground, which makes earthworks a strenuous task. Using a pickax instead of a shovel can help in removing the mail service.

• Shovel
• Pickax
• Heavy-duty chain
• Prefabricated mailbox mail service with arm
• Woods screws
• Electric screwdriver
• 2 boards, 1-by-iii-inches
• Hammer
• Mallet
• 2 wooden stakes
• ii bags quick-setting physical mix, fifty-lbs. each
• 3/4-inch-thick lath
• Saw

Tip

Purchase a replacement mailbox kit at a hardware shop that includes the necessary hardware and instructions for attaching it to the post.

Alert

Check with your local post office for curbside mailbox regulations governing the elevation and altitude from the road.

1. Cascade hot water -- a gallon at a time -- over the frozen footing around the mailbox post to help soften it.

2. Dig 3 to four inches effectually the damaged mailbox post with a shovel, or a pickax if the ground is frozen. Motility the post in a dorsum-and-along motion to loosen information technology from the ground.

3. Adhere a heavy-duty chain around the damaged mailbox post. Secure the other end of the chain to a truck hitch or a four-wheeler. Press the vehicle's gas pedal gently until the chain is taut, then slowly continue until the force of the vehicle jerks the damaged mailbox mail out of the footing.

4. Make clean dirt and other debris from inside the post hole. Place the prefabricated post with mailbox arm in the center of the hole. Back up the mail service in position by angling ane of the 1-by-3-inch boards from i side of the post to the footing. Secure the board to the post with forest screws and a screwdriver. Adhere the other board to the reverse side of the post and angle it away from the post. Make sure the braces are perpendicular.

5. Pound a wooden stake near the base of each lath. Screw each board to its wooden stake to secure the braces. Make certain the post is standing straight.

6. Dump 1 50-pound bag of quick-setting concrete mix into the posthole. Pour i gallon of water into the hole. Mix the contents with a shovel.

7. Dump a second bag of the quick-setting concrete mix and some other gallon of water into the posthole. Mix well with the shovel. Let the concrete to set for 24 hours.

8. Cut a 3/four-inch-thick board long plenty to run nether the bottom of the mailbox, using a saw. Secure it to the arm of the mail service with several screws. Attach the mailbox to the post using the included hardware. Fill the posthole with pinnacle soil.

The Drip Cap

• The winter months can wreak havoc on your mailbox.
  
• Vehicles sliding on the ice, snowplows trying to clear the roads and the extra weight of snow and ice can snap and cleft your mailbox and post, damaging them beyond repair.
  
• This tin be a difficult task during the winter season.
  
• Dig three to four inches around the damaged mailbox post with a shovel, or a pickax if the footing is frozen.
  
• Secure the lath to the postal service with wood screws and a screwdriver.
  
• Make sure the braces are perpendicular.
  
• Dump a second bag of the quick-setting concrete mix and another gallon of water into the posthole.

Source: https://homesteady.com/13425182/how-to-replace-a-mailbox-in-the-winter

Posted by: hendersontriessir1989.blogspot.com

Share this post